PIC24HJXXXGPX06A/X08A/X10A Data Sheet (03/29/2011)

PIC24HJXXXGPXXXA 16-bit General Purpose Microcontroller with seamless migration options from/to PIC24F, dsPIC30F and dsPIC33F devices. These devices are avialble with Extended temperature options Parameter Name  Value  Architecture  16-bit  CPU Speed (MIPS)  40  Memory Type  Flash  Program Memory (KB)  256  RAM Bytes  16,384  Temperature Range C  -40 to 125  Operating Voltage Range (V)  3 to 3.6  I/O Pins  53  Pin Count  64  System Management Features  PBOR  POR  Yes  WDT  Yes  Internal Oscillator  7.37 MHz, 512 kHz  nanoWatt Features  Fast Wake/Fast Control  Digital Communication Peripherals  2-UART, 2-SPI, 2-I2C  Codec Interface  NO  Analog Peripherals  1-A/D 18x12-bit @ 500(ksps)  Capture/Compare/PWM Peripherals  8/8  PWM Resolution bits  16  Timers  9 x 16-bit 4 x 32-bit  Parallel Port  GPIO  Hardware RTCC  No  DMA  8  XLP  NO   Features Operating Range: •   DC – 40 MIPS (40 MIPS @ 3.0-3.6V, -40°C to +125°C) •   Industrial temperature range (-40°C to +85°C) •   Extended temperature range (-40°C to +125°C)High-Performance  CPU: Modified Harvard architecture •   C compiler optimized instruction set •   16-bit wide data path •   24-bit wide instructions •   Linear program memory addressing up to 4M instruction words •   Linear data memory addressing up to 64 Kbytes •   71 base instructions: mostly 1 word/1 cycle •   Sixteen 16-bit General Purpose Registers •   Flexible and powerful Indirect Addressing modes •   Software stack •   16 x 16 multiply operations •   32/16 and 16/16 divide operations •   Up to ±16-bit data shifts. Direct Memory Access (DMA):  8-channel hardware DMA •   2 Kbytes dual ported DMA buffer area (DMA RAM) to store data transferred via DMA: - Allows data transfer between RAM and a peripheral while CPU is executing code (no cycle stealing) •   Most peripherals support DMA. Interrupt Controller:  5-cycle latency •   118 interrupt vectors •   Up to 61 available interrupt sources •   Up to 5 external interrupts •   7 programmable priority levels •   5 processor exceptions Digital I/O:  •   Wake-up/Interrupt-on-Change on up to 24 pins •   Output pins can drive from 3.0V to 3.6V •   All digital input pins are 5V tolerant •   4 mA sink on all I/O pins  System Management:  •   Flexible clock options: - External, crystal, resonator, internal RC - Fully integrated PLL - Extremely low jitter PLL •   Power-up Timer •   Oscillator Start-up Timer/Stabilizer •   Watchdog Timer with its own RC oscillator •   Fail-Safe Clock Monitor •   Reset by multiple sources  Power Management:  •   On-chip 2.5V voltage regulator •   Switch between clock sources in real time •   Idle, Sleep and Doze modes with fast wake-up  Timers/Capture/Compare/PWM:  •   Timer/Counters, up to nine 16-bit timers: - Can pair up to make four 32-bit timers - 1 timer runs as Real-Time Clock with external 32.768 kHz oscillator - Programmable prescaler •   Input Capture (up to 8 channels): - Capture on up, down or both edges - 16-bit capture input functions - 4-deep FIFO on each capture •   Output Compare (up to 8 channels): - Single or Dual 16-Bit Compare mode - 16-bit Glitchless PWM mode  Communication Modules:  •   3-wire SPI (up to 2 modules): - Framing supports I/O interface to simple codecs - Supports 8-bit and 16-bit data - Supports all serial clock formats and sampling modes •   I2C™ (up to 2 modules): - Full Multi-Master Slave mode support - 7-bit and 10-bit addressing - Bus collision detection and arbitration - Integrated signal conditioning - Slave address masking •   UART (up to 2 modules): - Interrupt on address bit detect - Interrupt on UART error - Wake-up on Start bit from Sleep mode - 4-character TX and RX FIFO buffers - LIN bus support - IrDA® encoding and decoding in hardware - High-Speed Baud mode - Hardware Flow Control with CTS and RTS •   Enhanced CAN (ECAN™ module) 2.0B active (up to 2 modules): - Up to 8 transmit and up to 32 receive buffers - 16 receive filters and 3 masks - Loopback, Listen Only and Listen All Messages modes for diagnostics and bus monitoring - Wake-up on CAN message - Automatic processing of Remote Transmission Requests - FIFO mode using DMA - DeviceNet™ addressing support. Analog-to-Digital Converters:  •   Up to two A/D modules in a device •   10-bit, 1.1 Msps or 12-bit, 500 ksps conversion: - 2, 4 or 8 simultaneous samples - Up to 32 input channels with auto-scanning - Conversion start can be manual or synchronized with 1 of 4 trigger sources - Conversion possible in Sleep mode - ±2 LSb max integral nonlinearity - ±1 LSb max differential nonlinearity  CMOS Flash Technology:  •   Low-power, high-speed Flash technology •   Fully static design •   3.3V (±10%) operating voltage •   Industrial temperature •   Extended temperature •   Low-power consumption.   PIC24HJXXXGPX06A/X08A/X10A Data Sheet