dsPIC30F General Purpose 16-bit Digital Signal Controller. Seamless migration options from this device to dsPIC33F and PIC24 devices in similar packages.

 

Parameter Name	Value
Architecture	16-bit
CPU Speed (MIPS)	30
Memory Type	Flash
Program Memory (KB)	66
RAM Bytes	4,096
Temperature Range C	-40 to 125
Operating Voltage Range (V)	2.5 to 5.5
I/O Pins	52
Pin Count	64
System Management Features	PBOR, LVD
POR	Yes
WDT	Yes
Internal Oscillator	7.37 MHz, 512 kHz
nanoWatt Features	Fast Wake/Fast Control
Digital Communication Peripherals	2-UART, 2-SPI, 1-I2C
Codec Interface	Yes
Analog Peripherals	1-A/D 16x12-bit @ 200(ksps)
Comparators	0
CAN (#, type)	2 CAN
Capture/Compare/PWM Peripherals	8/8
Timers	5 x 16-bit 2 x 32-bit
Parallel Port	GPIO
Hardware RTCC	No
DMA	0

Features

High-Performance Modified RISC CPU:

 Modified Harvard architecture

 C compiler optimized instruction set architecture

 84 base instructions with flexible addressing modes

 24-bit wide instructions, 16-bit wide data path

 16 x 16-bit working register array

 Up to 30 MIPs operation:

            - DC to 40 MHz external clock input

            - Internal FRC input with PLL active (4x, 8x, 16x)

            - 4 MHz-10 MHz oscillator input with PLL active (4x, 8x, 16x)

 Peripheral and External interrupt sources

 8 user selectable priority levels for each interrupt

 4 processor exceptions and software traps

 Primary and Alternate interrupt Vector Tables

DSP Engine Features:

 Modulo and Bit-Reversed Addressing modes

 Two, 40-bit wide accumulators with optional saturation logic

 17-bit x 17-bit single cycle hardware fractional/ integer multiplier

 Single cycle Multiply-Accumulate (MAC) operation

 40-stage Barrel Shifter

 Dual data fetch

Peripheral Features:

 High current sink/source I/O pins: 25 mA/25 mA

 Optionally pair up 16-bit timers into 32-bit timer modules

 3-wire SPI™ modules (supports 4 Frame modes)

 I2C™ module supports Multi-Master/Slave mode and 7-bit/10-bit addressing

 Addressable UART modules with FIFO buffers and selectable pins

 Data Converter Interface (DCI) supports common audio Codec protocols, including I2S and AC’97

Analog Features:

 12-bit 200 Ksps Analog-to-Digital Converter (A/D)

 A/D Conversion available during Sleep and Idle

 1 Sample/Hold

 Multiple Conversion Sequencing Options

Special Microcontroller Features:

 Enhanced Flash program memory:

            - 10,000 erase/write cycle (min.) for industrial temperature range, 100K (typical)

 Data EEPROM memory:

            - 100,000 erase/write cycle (min.) for industrial temperature range, 1M (typical)

 Self-reprogrammable under software control

 Power-on Reset (POR), Power-up Timer (PWRT) and Oscillator Start-up Timer (OST)

 Flexible Watchdog Timer (WDT) with on-chip low power RC oscillator for reliable operation

 Fail-Safe clock monitor operation

 Detects clock failure and switches to on-chip low power RC oscillator

 Programmable code protection

 In-Circuit Serial Programming™ (ICSP™)

 Programmable Brown-out Detection and Reset generation

 Selectable Power Management modes

            - Sleep, Idle and Alternate Clock modes

           

CMOS Technology:

 Low power, high speed Flash technology

 Wide operating voltage range (2.5V to 5.5V)

 Industrial and Extended temperature ranges

dsPIC30F5011/5013 Data Sheet